Luth-AR MBA-3 "FDE" Carbine Stock AR15 AR-15 Collapsible AR10

Luth-AR MBA-3 Carbine Stock Collapsible fits AR10 or AR15 Milspec & Commercial

The Luth-AR Modular Buttstock Assembly (MBA) for AR style carbines is designed to replace the standard buttstock on your AR. The MBA-3 Carbine Buttstock is designed to work with a 6-position Mil-Spec or Commercial buffer tube. The MBA-3 features a 3-Axis Buttplate with Length-of-Pull adjustment as well as height and lateral adjustments, and an adjustable cheek rise in a low-cost, lightweight, strong and high-quality design.

The MBA-3 requires a Carbine buffer tube, either Mil-Spec or Commercial. Please review the information provided in the Requirements tab. This stock works with both carbine Commercial and Mil-Spec tubes/assemblies.

The MBA-3 also features an anti-rattle set screw. The modular design of the MBA Buttstock allows you to configure your buttstock to your specific and personal needs. Includes a rail attachment for attaching a monopod. The MBA features multiple attachment points for a sling, including molded pockets that will accept Grovtec QD cups, sold separately.

Product Description

Fully Adjustable Carbine Buttstock assembly to mount to a carbine rifle (6-positions mil-spec or commercial tube) – This is our carbine stock. Additional 1? height on cheek rest. 3-axis Adjustable Butt Plate Assembly extends additional 1 1/16? length of pull and includes the following movement:

1. Horizontal for linear adjustment (i.e. length of pull)
2. Vertical for a perfect butt plate fit into the curvature of the shoulder.
3. Lateral adjustment for a ½ inch left or right cast
   

This Luthar MBA3 butt plate assembly is interchangeable with the original MBA-1 Buttstock. Includes a Picatinny Rail on the bottom rear of the Stock Body to attach your choice of many accessories such as our Accushot Monopod. Designed a flat bottom index set screw (10-24) to eliminate that constant rattle of carbine collapsible buttstocks. This also allows you to secure the stock in your favorite position. Comes with hard butt plate as a pad. A medium hard rubber recoil pad is available for additional purchase. The Luth-AR MBA-3 weighs roughly half that of comparable stocks coming in at just 18.5 ounces.

• Fits all .223 and most .308 AR carbine style rifles
• Super Strong Glass Filled Nylon
• Easy to replace and quick to install
• Uses 4 out of the 6 positions on a mil-spec or commercial tube
  

Features

• Ergonomic
• Adapts To Existing Commercial and Mil-Spec Buffer Tubes (Certain after Market Commercial Buffer Tubes that exceed 1.172? may not fit)
• The vertical struts for the MBA 3 are fixed therefore the cheek piece is not reversible like the MBA 1 however the cheek piece itself is designed with a cheek pad for the lefty
• NOT interchangeable with A2 standard FIXED buffer tube. You will need to purchase a MBA-1 or MBA-2 to fit the A2 tubes.
  

Compatible Buffer Assemblies:

• .223 Mil-Spec Carbine Buffer Assembly
• .223 Commercial Carbine Buffer Assembly
• .308 Mil-Spec Carbine Buffer Assembly
• .308 Commercial Carbine Buffer Assembly
  

Additional Information

It does not include the following, but can be purchased separately:

• Medium hard rubber recoil pad
• Sling Swivels
• Carbine Buffer Tube Kit (Milspec tube, buffer, spring, castle nut, locking plate) in AR15 or AR10 sizes
  
• Carbine Buffer Body
  

Installation Notes:  

When tightening the anti rattle set screw, be careful not to over tighten as it may cause the threaded insert to separate from the plastic stock body. When sliding on 6-position tube, the lock pin has a notch in the head of the lock pin that will line up with the stock body. This needs to be lined up before sliding on the tube. The tube will slide on easily without resistance. If there is any resistance, that lock pin is not in its place.